Home > Products > Universal key Cutting Machine

Universal key Cutting Machine

S.P.C 101

Characteristics

  • 1)

    This machine is only one patented Universal Key Cutting Machine in the world mounted 4 kinds of keys classified globally i.e.This machine (M/C) is only one patented Universal Key Cutting M/C in the world mounted below 4 kinds of key classified globally i.e.,

  • 1)

    Ordinary keys such as American Lock Co. USA and Car keys

  • 2)

    Key of Mul -T-Lock, Israel

  • 3)

    Key of Medeco,USA and

  • 4)

    Key of vending(slot) M/C & Key of Profalux, France wholly.

  • 2)

    No need to set the balance point at zero (0) without changing tools, only usable necessary tool after selection due to it has already mounted 10 kinds of cutted tools in the machine.

  • 3)

    This is a patented new developed cam (lever ) type machine giving uniform force not geared type giving excessive force to tools so it reduces product defect.

  • 4)

    This machine has an effect installed the above four (4) kinds of key machines by one machine and so it needs only small space.

  • 5)

    This machine has semi -permanent life cycle mounted 10 kinds of tools including six(6) ultrahard tools and each of two(2) cutter and endmill. Name & No. of tools are shown on the label.

Power Weight Width Length Heigh
220V 24.3kg 270mm 410mm 435mm

* Dimensions can be revised for promotion of quality

How to use

  • 1)

    The Main Switch⑳ on and the lights on, the Spindle Switch⑲ on and the machine start, the Main Handle ⑮ put down and the tool spindle rotate (after confirmed by sound of the spindle and the tools get combined), the Main Handle⑮ put up and the machine stop.

  • 2)

    Depending on the type of key you want to cut, select the tool (shown on the nameplate) and for the change of tool, put the Tool Change Handle ⑰ into the Tool Change Hole⑱ between tools, and rotate tools to meet with same number of Guide⑨ as the desired tool number.

  • 3)

    For the selection of Guide⑨, turn the Guide Change Screw Pin⑥ on the left and take it off, and after meet it with same number of tool on the right , turn the Guide Change Screw Pin⑥ on clockwise again and lock it slightly not too much.

  • 4)

    In the event of tool wear or break, for set of the tool balance point to zero (0), set the flat keys on the left and right side of the vise with the same thickness of flat key and then use T wrench⑯ and loosen the Guide Fix Screw⑦, and turn it on the left in 9 o’clock and the right 3 o’clock pressing the Main Handle ⑮ slightly , then the tool and the Guide ⑨ become match to the balance point zero (0). When the Guide Fix Screw⑦ is turned on the left, it will be deep and turned on the right, it will be shallow.

  • 5)

    In time of cutting normal keys or car keys such as American Lock’s key, turn and set the Table Forward/Backward Transfer Pin㉒ on the right until sounded and move the Vise⑫ to the front of operator by the Table Forward /Backward Transfer Handle ⑭ , after set the original key and the flat key on the vise, turn down the Main Handle⑮ to the end and lock the Guide Spindle Fix Screw ② and loosen the Vise Jump Handle⑪ to lift up and then after set the flat key to center part of the rotary cutter, lock the Table Left/Right Fix Screw⑬ and set the Guide⑨ to sloping front part of the original key and turn the Table Forward /Backward Transfer Handle ⑭ slowly , the Vise⑫ will move forward grooving self up-down by a spring mounted, and then the flat key shall be cutted and finally when it moves reversely , it shall be removed burr for more clean cutted key.

  • 6)

    In time of cutting for right angled ordinary keys, put down the Vise Jump Handle⑪ and fix it and bite the original key and the flat key to the groove of the general key bite and then cut the flat key using the Main Handle⑮.

  • 7)

    In time of cutting Medeco keys (off-angled), set the Guide⑨ to same rail direction as original keys and move it on the grooved direction of the original key using the Table Transfer Handle⑤ pressing the Main Handle⑮ gently and then replicate the flat key moving left and right as slowly as possible.